 |
| Overstock Parts - for more information
contact Susan at (800)890-2111 Click
here for a printer friendly version |
| DuraKool AFM15-309-M - $4.99 |
DuraKool AFM220-309- $9.99 |
 |
 |
| The DuraKool15 amp single pole mercury
displacement relay is used for lighting controls, energy management
systems, light inductive, and motor loads. The maximum operating time
is 90 ms and the release time is 150 ms. There is no contact bounce.
The load connectors as well as the coil terminals are ¼”
male quick connects. The breakdown voltage is 2000 VRMS/Min. Across
Contacts.The coil data for these 12 volt dc coils is as follows: Ohms
= 62; Watts = 2.3; Amps = 0.192. |
This is a double pole 20 amp relay.
The 12 volt dc coil ratings are as follows: Ohms = 33.2; Watts = 4.32;
Amps = 0.36. Maximum operating time is 90 ms. Release time is 150
ms. The load connectors are ¼” male quick connects as
are the coil terminals. The breakdown voltage for this relay is 2000
VRMS/Min. Across Contacts. There is no contact bounce. Popular uses
for these mercury displacement relays are: lighting controls, energy
managements systems, light inductive and motor loads. |
| DuraKool BFL2-7041 - $14.99 |
|
 |
|
| These are 35 amp mecury displacement
relays by DuraKool with part number BFL2-7041. They are also known
as 35 amp general purpose contactors. The contacts are normally open.
They have two poles. The top and bottom lugs accept up to a #4 AWG
copper wire. The control coil is 12 volts DC using 6-32 wire binding
screws for termination. The DC coil ohms are 24, coil watts are 6,
coil amps are 0.5. The maximum time to operate is 70 ms, with a release
time of 90 ms. There is no contact bounce with these mecury displacement
relays. Breakdown voltage: 5000 VRMS/Min. Across Contacts. |
|
| DORMA 7801 TJ RH SN1 AL - $39.88 |
DORMA TS83-7 AL - $60.00 |
 |
 |
| This is a hydraulic surface-applied
rack and pinion closer. It is adjustable from size 1 to 5 to meet
interior or exterior door barrier-free requirements. It is made to
mount on the top of the door jamb and is for right handed doors. It
has a full metal cover with 3” projection, 2 ¾”
height and 11 3/8” length. The cover conceals the closer body
and the adjustment valves. It has two non-critical adjusting valves
for sweep and latch that have thermostatic properties with a special
hydraulic fluid to provide consistent closing speeds under a wide
variety of temperatures. It is U.L. listed. It is certified to conform
to the requirements of ANSI A156.4 Grade 1. The sprayed finish is
aluminum. |
This kit includes a Dorma TS 83
series closer body and hardware with an instruction sheet showing
how to install the closer on a pocketed door. Pocketed doors are generally
built into the wall so that when open, they are flush with the wall.
The arm is not included in the kit. |
| DORMA TS93-6 PS MAX AL - $115 + Arm |
DORMA TS93-6 PS-MAX AL LESS ARM -
$115.00 |
 |
 |
| This is a hydraulic surface applied closer with steel
cam, roller and adjustable spring, and it incorporates a track arm
assembly. It has two separate temperature compensating, non-critical
adjustment valves to control sweep and latch closing speeds. It also
has adjustable hydraulic back-check that takes effect at approximately
65 degrees. It is adjustable for 75% additional closing force over
the base size 6 for exceptionally wide, tall, or heavy doors. The
maximum opening range is approximately 175 degrees for pull-side installations
and 135 degrees for push-side installations. It is non-handed. |
This kit is a basic TS 93 series closer body with hardware.
No arm is included |
| Sprockets |
| 013192 Sprocket 50C21 - $32.70 EA |
017242 Sprocket 25B11 1/4 - $6.52
EA |
 |
 |
| 017243 Sprocket 25B15 1/4 - $1.31
EA |
017305 Sprocket 25B25 1/2" - $12.40
EA |
 |
 |
| 017306 Sprocket 25B19 3/4 - $1.73
EA |
017381 Sprocket 25b40 3/4" - $4.92
EA |
 |
 |
| 017441 Sprocket 25B19 1/4" - $2.85
EA |
017442 Sprocket 25B22 1/4" - $4.75
EA |
 |
 |
